Special Service Tool EES000LC The actual shapes of KentMoore tools may differ from those of special service tools illustrated here Tool number (KentMoore No) Tool name Description (J) Transmitter activation tool ID registration LEIA0035ESpecial Tools 50 Air Conditioning 93 Automatic Transmission 6 Certified Collision Repair 28 CONSULT 25 Cool Tools 72 Differential & Axle 300 Engine & Electrical Electronic 395 Engine & Electrical General 58 EV Tools 66 Fuel & Emission Control Engine 261 General Hand Tools 15 HEV Tools 16 Manual Transmission & Clutch 53 Steering & Brakes 10 Supplemental RestraintNew replacement transmitters are provided "asleep" and must first be "woken up" using Transmitter Activation Tool J before ID registration can be performed 1 Turn ignition switch ON Push the transmitter activation tool against the tire near the front left transmitter Press the button for 5 seconds The hazard warning lamps flash per the following diagram 2
Transmitter activation tool j 45295
Transmitter activation tool j 45295-The ID registration can either be performed with the Transmitter Activation Tool JA (new model), the J (old model), the Signal Tech II tool (J) and CONSULT III plus (CIII plus), or manually The Signal Tech II not only is used for ID registration, but some of its other functions include displaying the tire pressures reported by the TPMS transmitters and readingNew replacement transmitters are provided "asleep" and must first be "woken up" using Transmitter Activation Tool J before ID registration can be performed 1 Turn ignition switch ON Push the transmitter activation tool against the tire near the front left transmitter Press the button for 5 seconds The hazard warning lamps flash per the following diagram Tool number (J
New replacement transmitters are provided "asleep" and must first be "woken up" using Transmitter Activation Tool J before ID registration can be performed 1 Turn ignition switch ON Push the transmitter activation tool against the tire near the front left transmitter Press the button for 5 seconds The hazard warning lamps flash per the following diagram Tool number (JTool J, or Transmitter Activation tool (JA) can be used to register TPMS/LTPWS sensors NOTE Failure to update Signal Tech II may lead to misdiagnosis of vehicles built after • The latest software is available on the CONSULT III PC at ASIST > Tools & Equipment > Nissan TECHMATE > Nissan TECH MATE Web Site > Service tools > Signal Tech IIUs e the following procedure when using the Transmitter Activation Tool J NOTE The Signal Tech II Tool (J) can be used to perform the following functions Refer to the Signal Tech II User Guide for additional information • Activate and display TPMS transmitter IDs • Display tire pressure reported by the TPMS transmitter • Read TPMS DTCs • Register TPMS transmitter
Versión en línea gratuita de Mitchell onDemand (proDemand)Hold the transmitter activation tool (JA) (1) against the side of the left front tire, near the valve stem 5 With the tool held at a 0 to 15 degree angle to the tire, press and hold the transmitter activation tool button until the indicator lamp turns OFF (approximately 5 seconds) 6 Repeat steps 4 and 5 for the remaining tires in this order right front, right rear and left rearCompatible with future sensors;
Equipped with a display (KV only) Commercial Service Tool Tool name Description Power tool Loosening nuts, screws and bolts Precaution Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRETENSIONER" TheFree online version of Mitchell onDemand (proDemand)New replacement transmitters are provided "asleep" and must first be "woken up" using Transmitter Activation Tool J before ID registration can be performed Connect CONSULTIII Select "ID REGIST" under BCM Push the transmitter activation tool against the tire near the front left transmitter Press the button for 5 seconds Tool number (J)
Aclk Sa L Ai Dchcsewiqlp66lsfzahucda0ghwyydfyyabafggjwdg Sig Aod64 3grt8x2scgojly0rupr10axyxh0a Adurl Ctype 5
0 件のコメント:
コメントを投稿